DIY Smart Home: Build Your Own Automatic Water Pump Switch and Save Water

Automatic Water Pump Switch Electronic Schematic
(Source: Easy Electronic Project)

Smart Home Technology has revolutionized the way we live our lives. It has made our homes more efficient, convenient, and secure. With the advent of easy-to-use and affordable electronic components, anyone can now create their own smart home system. This has led to an increase in DIY smart home projects that can be easily customized to meet specific needs and preferences.

One popular aspect of smart home technology is automated water management. This includes everything from detecting leaks to controlling water usage. One of the most common and useful automated water management systems is an automatic water pump switch. This system ensures that water is only pumped when it is needed, which saves water and energy. In this article, we will guide you on how to build your own automatic water pump switch using simple electronic components.

Introduction:

Water is a vital resource for our daily lives, but it can be difficult to manage the amount of water used in a household. One way to manage water usage is by using an automatic water pump switch. In this mini project, we will guide you on how to build your own automatic water pump switch using simple electronic components.

Materials Needed:

1. Arduino Uno board
2. Relay module
3. 5V power supply
4. Water pump
5. Jumper wires
6. Water level sensor

Instructions:

• Connect the VCC and GND pins of the water level sensor to the Arduino Uno's 5V and GND pins respectively.
• Connect the output pin of the water level sensor to digital pin 2 of the Arduino Uno.
• Connect the VCC and GND pins of the relay module to the 5V and GND pins of the Arduino Uno respectively.
• Connect the IN1 pin of the relay module to digital pin 3 of the Arduino Uno.
• Connect the NO (normally open) and COM (common) pins of the relay module to the power supply and the water pump respectively.
• Upload the following code to the Arduino Uno:

• Power up the Arduino Uno with the 5V power supply.

How it Works:

The water level sensor detects the water level in a container and sends a signal to the Arduino Uno. If the water level is low, the signal is low, and the Arduino Uno sends a signal to the relay module to turn on the water pump. If the water level is high, the signal is high, and the Arduino Uno sends a signal to the relay module to turn off the water pump.

Conclusion:

In this mini project, we have shown you how to build your own automatic water pump switch using an Arduino Uno board and a few simple electronic components. By building this project, you can ensure that your water pump only runs when it is needed, saving water and energy.

An automatic water pump switch is a useful addition to any smart home system, especially for those who want to conserve water and energy. By following the instructions in this article, you can build your own automatic water pump switch with just a few electronic components and an Arduino Uno board. Once you have built your system, you can customize it to suit your specific needs and preferences. To learn more about other DIY smart home projects and technologies, you can explore various online resources and tutorials HERE. Happy building!

Read More

Proteus Design and Simulation Version 8.15 Download: A Comprehensive Guide

Proteus Design and Simulation is a popular software tool used by engineers and designers to simulate and test electronic circuits before they are physically built. The latest version of the software is Proteus 8.15, which offers a range of new features and improvements.

Proteus Design and Simulation Version 8.15 Download
(Source: FileCR)

One of the most significant improvements in Proteus 8.15 is the enhanced support for microcontroller simulation. This makes it easier to design and test complex electronic systems that involve microcontrollers and other digital components.

The new version of Proteus also includes a range of new components and models, making it easier to design and simulate a wide range of electronic circuits. These include new sensors, transistors, and microcontrollers, among others.

Proteus 8.15 also includes improvements to the schematic capture and PCB layout tools. This makes it easier to design and layout electronic circuits quickly and efficiently, saving designers time and effort.

Another significant improvement in Proteus 8.15 is the enhanced 3D visualization capabilities. The software now allows designers to visualize their circuits in 3D, which makes it easier to identify any potential issues and optimize the design for performance.

In addition to these new features and improvements, Proteus 8.15 also includes a range of bug fixes and performance enhancements. This ensures that the software runs smoothly and reliably, providing designers with a stable and efficient platform for designing and simulating electronic circuits.

To download Proteus 8.15, users can visit the official website of Labcenter Electronics, the company behind the software. The software is available for both Windows and Mac platforms, and users can choose between different versions based on their specific needs and requirements.

Before downloading and installing Proteus 8.15, users should ensure that their system meets the minimum system requirements. This includes a compatible operating system, sufficient memory and storage space, and a reliable internet connection.

Once the software has been downloaded and installed, users can start exploring its new features and capabilities. Proteus 8.15 is designed to be intuitive and easy to use, with a range of tools and resources available to help designers get started quickly.

In conclusion, Proteus Design and Simulation version 8.15 is a powerful and reliable software tool for designing and simulating electronic circuits. With its range of new features and improvements, it provides designers with an efficient and effective platform for designing complex electronic systems.

Read More

Free Download Proteus Professional Version 8.9 SP2 Build 28501 with Install Instruction

Proteus Software. - In this article we will continue to give you the next version of Proteus 8 Professional software. Now we will give you the next version of Proteus Professional Version 8.9 SP2 Build 28501 with Install Instruction to complete your collection of this software.

Proteus Professional Version 8.9 SP2 Build 28501

Beside you can read the description about the Proteus 8, you also can follow the instruction on how you can install Proteus Professional Version 8.9 SP2 Build 28501 after you download this software based link given in this blog.

Description

Proteus is a powerful Computer Aided Design (CAD) software that was especially designed to help designers build and verify the circuit boards easily. By using this software you can create a highly complex electrical circuit designs requires not only solid knowledge, but also a set of tools to get the job done. Proteus PCB Design enables you to design a PCB which there are very detailed electrical components such as microcontrollers, microprocessors, and other components are often used in electrical circuits.

Proteus Professional provides an interactive simulations and customizations tools that enables designers to view and edit the properties of every element on the board. It help you design, test and layout professional PCBs like never before. The design can be edited, simulated, verified, as well as exported. Proteus Design Suite delivers the complete software package for today and tomorrow’s engineers with VSM simulation and new flowchart engine that provide a truly integrated and intuitive development environment. 

Installation Guide

After you download the Proteus Professional Version 8.9 SP2 Build 28501 using link below, now you can follow the instruction to install this software in your computer or laptop based on watching the video from Youtube using link below.

Installation Video for Proteus Professional Version 8.9 SP2 Build 28501

Download

And now you can click the links below to download Proteus Professional Version 8.9 SP2 Build 28501 with Install Instruction freely and easily.

Download Proteus Professional Version 8.9 SP2 Build 28501 with Install Instruction | 384 MB

Read More

Free Download Recent Proteus 8.9 Professional SP2 Full Crack for Windows System

Proteus Software. - In this article we will continue to give you the next version of Proteus Professional software. Now we will give you the next version of Recent Proteus 8.9 Professional SP2 Full Crack for Windows System with Free Download to complete your collection of this software.

Image Courtesy of Mazterize

Description

Proteus is a powerful Computer Aided Design (CAD) software that was especially designed to help designers build and verify the circuit boards easily. By using this software you can create a highly complex electrical circuit designs requires not only solid knowledge, but also a set of tools to get the job done. Proteus PCB Design enables you to design a PCB which there are very detailed electrical components such as microcontrollers, microprocessors, and other components are often used in electrical circuits.

Accordingly from Mazterize site describe that Proteus Professional provides an interactive simulations and customizations tools that enables designers to view and edit the properties of every element on the board. It help you design, test and layout professional PCBs like never before. The design can be edited, simulated, verified, as well as exported. Proteus Design Suite delivers the complete software package for today and tomorrow’s engineers with VSM simulation and new flowchart engine that provide a truly integrated and intuitive development environment.

Key features:

• Ease of use with powerful features
• Design, test and layout PCBs with ease
• More than 800 microcontroller variants
• Intuitive professional PCB layout packages
• Integrated suite of tools for PCB Design
• Very intuitive development environment
• Co-simulate micro-controller simulation
• And so much more.

What’s new in Proteus 8.9:

1. Schematic symbols and PCB footprints
2. Upgraded the design rule manager
3. Properties for particular components
4. Other bug fixes and improvements.

Download

And now you can click the links below to download Recent Proteus 8.9 Professional SP2 Full Crack for Windows System freely and easily.

Download Proteus v8.8 SP1 Windows | 396.7 MB

Read More

Electronic Software: Proteus v8.8 SP1 for Windows Free Download

Proteus Software. - In this article we will continue to give you the next version of Proteus Professional software. Now we will give you the next version of Proteus Professional software that called with Proteus Professional v8.8 SP1 for Windows with Free Download to complete your collection of this software.

Image Courtesy of Google Image Search

Description

Proteus is a powerful Computer Aided Design (CAD) software that was especially designed to help designers build and verify the circuit boards easily. By using this software you can create a highly complex electrical circuit designs requires not only solid knowledge, but also a set of tools to get the job done. Proteus PCB Design enables you to design a PCB which there are very detailed electrical components such as microcontrollers, microprocessors, and other components are often used in electrical circuits.

Proteus Professional provides an interactive simulations and customizations tools that enables designers to view and edit the properties of every element on the board. It help you design, test and layout professional PCBs like never before. The design can be edited, simulated, verified, as well as exported. Proteus Design Suite delivers the complete software package for today and tomorrow’s engineers with VSM simulation and new flowchart engine that provide a truly integrated and intuitive development environment. (Master Kreatif)

Download

And now you can click the links below to download Proteus v8.8 SP1 for Windows freely and easily.

Download Proteus v8.8 SP1 Windows 

Read More

Electronic Project: Moisture sensing automatic plant watering system using 8051

Project. - This is one of implementation microcontroller MCS51 to build moisture sensing automatic plant watering system in this time. It is only need small component completed to build this project using microcontroller 8051 in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Blog Design

Figure 1. Circuit schematic of Moisture sensing automatic plant watering system using 8051 (Source: Circuitstoday.com)

Component Parts

• 8051 microcontroller
• Resistor
• Relay
• moisture sensing probe
• YL38 module
• Diode
• Pump motor 12V
• X-tal
• Capacitors
• LCD 16x2
• Resistor array

Description

According Circuitstoday blog mentioned that This project is about a moisture-sensing automatic plant watering system using 8051 microcontroller. The system simply senses the moisture level and switches on the irrigation pump when the moisture is below the set limit. The system switches off the pump when the moisture rises above the set point. The moisture level threshold can be set using a trim pot on the system. The status of the pump (whether ON or OFF) is displayed on a 16×2 LCD display. The system can be divided into three section as follows.

Sensing prob.

YL 69 moisture sensing probe is used to sense the moisture here. It is simply a fork-shaped PCB with tracks running on both sides of the legs.  Just plug this probe into the soil where you want to sense the moisture.

Comparator circuit.

YL 38 comparator module is used in this project. It is a single channel opamp comparator based on L393 IC. This module just compares the output voltage of the sensing probe with a reference voltage and switches its voltage appropriately for the microcontroller to read. 

Read More

Electronic Circuit: Amplifier Power Supply 24V 2A Based on TIP122

Converter. - There are many sound system power amplifier need best quality power supply to get best sound in this time. One of the power supply to supply 30W power amplifier is 24V 2A power supply using or based on TIP122 look like shown in Figure 1 below.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. Electronic Circuit: Amplifier Power Supply 24V 2A Based on TIP122 (Source: Eleccircuit.com)

Component Parts

• Transistor TIP122
• Transformer 5A
• Resistors
• Capacitors
• Zener Diodes 12V
• LED
• Diodes 1N5407

Description

This is electronic circuit of Electronic Circuit: Amplifier Power Supply 24V 2A Based on TIP122 for you. According Eleccircuits blog mentioned that when the load-use many currents. The output voltage still voltage of 24V, and low ripple. So low noise on the speaker of your amplifier. Of cause, we can use this circuit for any circuit and can change voltage output as you need. And this circuit has a few parts and easy to buy in most of the local markets.

The AC-voltage to the power cord, transformer T1 changes 230VAC(PRI) to about 24VAC(Sec). Then, the rectifier bridge, D1 through D4, rectifies the AC into pulsating DC.

Next, A big electrolytic capacitor-C1 filter the pulsating DC to smooth DC voltage about of 36V. But this is not complete. Because of It is not DC regulated voltage of 24V at 2A.

After that, the DC voltage flow through the R1 to Zener Diodes (ZD1, ZD2) to keeps the voltage constant at 25V. This voltage across the base of Darlington transistor Q1 to bias it working full current more than of 2A.

The capacitors C2, C3, C4 acts as a storage capacitor to reduce the noise of output. This makes constant voltage across the output of 24V. The LED1 show power on of circuit, which the R3 is its limiting current resistor.

Read More

Electronic Software: Autodesk EAGLE Premium 8.6.1 for Windows Free Download

Proteus Software. - In this article we will continue to give you the next version of Autodesk EAGLE software after we posted the Eagle version 7.7 for Windows system from this blog. Now we will give you the next version of Autodesk EAGLE Premium 8.6.1 for Windows Free Download to complete your collection of this software.

Image Courtesy of http://www.worldfreeware.com

In this time, we will give you one of the oldest version of EAGLE software that called with PAutodesk EAGLE Premium 8.6.1 for Windows Free Download system for electronic software design. Beside we will give you description we also will allow you to take free download Autodesk EAGLE Premium 8.6.1 for Windows Free Download according the link given in this blog. So, please enjoy and read continue this article until finish.

Description

From Worldfreeware describe that EAGLE Premium 8 free download is a great solution for every electronic engineering who is looking to make a PCB design so easily. The main purpose of using this software it’s the simplicity and also the efficiency. from the first look at the software’s name, you will be confident because it’s an Autodesk product.

PCB design made easy. Make anything with EAGLE PCB design software. Powerful, easy-to-use tools for every engineer. Speed through complex board layouts with modern PCB routing tools. Quickly reuse subcircuits that remain synchronized between schematic and PCB. Escape your ball grid arrays (BGA) in seconds, not hours.

Features of EAGLE 8.6.1

Make any PCB design software you like, print it and start building your integrated circuit. Besides that, you can make complex board design by using some PCB modern tools. You can also Save your precious time by adding electronics component without drawing them.

Download

And now you can click the links below to download Proteus 8.6 Professional Full Crack for Windows freely and easily.

Download Autodesk EAGLE Premium 8.6.1 for Windows | 113.8 MB

Read More

Electronic Circuit: Simple Small High Volts Shock using 2SC1815 Transistor

Converter. - This is one of implementation of 2SC1815 transistor is to build small high voltage shock in this time. It is only need small component completed to build this project in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. Circuit of Simple Small High Volts Shock using 2SC1815 Transistor (Source: Eleccircuits)

Component Parts

• 2SC1815 Transistor or C458 or C1815 or C828
• Battery
• Resistors
• Transformer

Description

This is electronic circuit of Simple Small High Volts Shock using 2SC1815 Transistor for you. According Eleccircuits blog mentioned that this is small high volts shock circuit, pressure from the low current. It is perfect for fun play. In circuit has a few component just two small NPN transistors, 2 resistors and a transformer. So easy to builds and cheap!

When switch S1 close the circuit for feed power supply give with Q1 and Q2. By current flow through coil of transformer of the primary and touch limit current with R1 and R2 already change come in pin way B of Q1 and Q2.

It make Q1 and Q2 bias by transistor that bilateral alternate work all the time. When Q1 bias make have current flow change during a half on of coil primary and when Q2 make have current flow during a half below of coil primary.

Read More

Electronic Circuit: Simple Analog to Digital Converter using ADC0808

Converter. - This is one of implementation ADC0808 IC is to build simple analog to digital converter in this time. It is only need small component completed to build this project in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. Electronic circuit of Simple Analog to Digital Converter using ADC0808 (Source: Electronicszone)

Component Parts

• ADC0808 IC
• LEDs
• Power Supply

Description

This is electronic circuit of Simple Analog to Digital Converter using ADC0808 for you. According Electronicszone blog mentioned that Normally analogue-to-digital con-verter (ADC) needs interfacing through a microprocessor to convert analogue data into digital format. This requires hardware and necessary software, resulting in increased complexity and hence the total cost.

The circuit of A-to-D converter shown here is configured around ADC 0808, avoiding the use of a microprocessor. The ADC 0808 is an 8-bit A-to-D converter, having data lines D0-D7. It works on the principle of successive approximation. It has a total of eight analogue input channels, out of which any one can be selected using address lines A, B and C. Here, in this case, input channel IN0 is selected by grounding A, B and C address lines.

Usually the control signals EOC (end of conversion), SC (start conversion), ALE (address latch enable) and OE (output enable) are interfaced by means of a microprocessor. However, the circuit shown here is built to operate in its continuous mode without using any microprocessor. Therefore the input control signals ALE and OE, being active-high, are tied to Vcc (+5 volts). The input control signal SC, being active-low, initiates start of conversion at falling edge of the pulse, whereas the output signal EOC becomes high after completion of digitisation. This EOC output is coupled to SC input, where falling edge of EOC output acts as SC input to direct the ADC to start the conversion.
As the conversion starts, EOC signal goes high. At next clock pulse EOC output again goes low, and hence SC is enabled to start the next conversion. Thus, it provides continuous 8-bit digital output corresponding to instantaneous value of analogue input. The maximum level of analogue input voltage should be appropriately scaled down below positive reference (+5V) level.

Read More

Electronic Circuit: VHF Dip Meter Based on Transistors

Radio. - This is one of implementation transistors to build VHF Dip meter in this time. It is only need small component completed to build this project in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Image Courtesy of https://www.eleccircuit.com/

Component Parts

• Transistors
• Inductor
• Capacitors
• Resistors
• Variable resistors
• Battery

Description

VHF dip meter based on transistors high voltage generator using NE555 IC for you. According Eleccircuits blog mentioned that this is a simple VHF dip meter circuit.The DIP meter is the frequency meter by use the LC resonance circuit that adjustable until the frequency show peak amplitude. The circuit include variable frequency generator circuit, rectifier and a moving coil meter.

In the oscillator include two transistors T1 and T2. The tuning circuit include C1 and coil Lx this coil will is outside the metal box. When apply the power to circuit, the voltage from the oscillator will be rectifier by diodes D1 and capacitor C2. Then, send signal to P1 that use to adjust meter.

If bring the coil Lx near the others LC circuits, that resonance same the frequency is generated. This LC circuit will pull power from Lx, cause the lower voltage drop across the meter. The adjusting frequency by C1 if the frequency resonance can read frequency by the meter.

Read More

Electronic Circuit: High Voltage Generator using NE555

555 Circuit. - This is one of implementation NE555 IC to build high voltage generator in this time. It is only need small component completed to build this voltage generator in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. High Voltage Generator Circuit using NE555 (Source: www.circuitstoday.com)

Component Parts

• NE555
• Capacitors
• Resistors
• Transistor
• Variable resistors
• EHT Transformer

Description

The electronic circuit design like in Figure 1 above show you high voltage generator using NE555 IC for you. 

According Circuitstoday blog mentioned that this is first of all let me remind you that this circuit is a very dangerous one. The output voltage of this circuit is in Kilo volts and it can seriously injure you or kill you. Try this circuit only if you have enough experience dealing with high voltages. I have no responsibility on any hazards caused by the circuit. Be very careful. This is a humble request.

The circuit given here has three sections namely oscillator, switching stage and a step up stage. The oscillator is build around a NE555 timer operating at 25 KHz. The output of the NE555 coupled to the base of the power transistor TIP3055 which is the switching device. The power transistor drives primary of the step up transformer at 25 KHz and as a result a high voltage will be induced across its secondary.

Read More

Electronic Project: Gesture Controlled Robot Using Raspberry Pi

Project. - This is one of implementation Raspberry Pi to build gesture controlled robot in this time. It is only need small component completed to build this project using Raspberry Pi, Accelerometer and also RF Module in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Blog Design

Component Parts

• Raspberry Pi, 
• Accelerometer, 
• RF Module, 
• Memory Card, 
• Power supply, 
• Wires, 
• Encoder, 
• Decoder, 
• Motor Driver

Description

According Circuitstoday blog mentioned that this tutorial we are going to control a robot driven by two DC motors by simply using hand movements. There are different kind of sensors to detect your hand movement like flux sensors, Accelerometers and other gravity based sensors. So for wireless transmission we are going to use RF 434 module which transmit 4 bit data. 4 bit data means you can transmit 16 different combinations i.e., 0000 to 1111. Further in this tutorial we will use an encoder and decoder to avoid interference in the air interface. A motor driver will drive the motors from using the decoder data.

We use our Raspberry pi at the transmitter end to analyze the sensor data and to transmit a data combination to the motor driver to drive the motors accordingly so that the robot can hover around. We will be using a 12 V battery on robot to power the decoder module, receiver module and the motors. At the transmitter end sensors and transmitter encoder module is powered by raspberry pi itself.

Read More

Electronic Project: Heartbeat Sensor using Arduino (Heart Rate Monitor)

Arduino. - This is one of implementation heartbeat sensor and Arduino to build heart rate monitor in this time. It is only need small component completed to build this project usig heartbeat sensor in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. Circuit Schematic of Heartbeat Sensor using Arduino (Heart Rate Monitor) (Source: https://www.electronicshub.org/)

Component Parts

• Arduino UNO x 1
• 16 x 2 LCD Display x 1
• 10KΩ Potentiometer
• 330Ω Resistor (Optional – for LCD backlight)
• Push Button
• Heartbeat Sensor Module with Probe (finger based)
• Mini Breadboard
• Connecting Wires

Description

The electronic circuit design like in Figure 1 above show you Heartbeat Sensor using Arduino (Heart Rate Monitor) that written by Ravi. 

According Electronicshub blog mentioned that Heartbeat Sensor is an electronic device that is used to measure the heart rate i.e. speed of the heartbeat. Monitoring body temperature, heart rate and blood pressure are the basic things that we do in order to keep us healthy.

In order to measure the body temperature, we use thermometers and a sphygmomanometer to monitor the Arterial Pressure or Blood Pressure.

Heart Rate can be monitored in two ways: one way is to manually check the pulse either at wrists or neck and the other way is to use a Heartbeat Sensor.

In this project, we have designed a Heart Rate Monitor System using Arduino and Heartbeat Sensor. You can find the Principle of Heartbeat Sensor, working of the Heartbeat Sensor and Arduino based Heart Rate Monitoring System using a practical heartbeat Sensor. 

Read More

Electronic Circuit: DIY Motion Sensor Light using LED Bulb and PIR Sensor by Narasimha Rao

8051 Circuit. - This is one of implementation PIR sensor to build motion sernsor light. It is only need small component completed to build motion sensor light in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. Electronic Circuit: DIY Motion Sensor Light using LED Bulb and PIR Sensor (Source: Circuitstoday.com)

Component Parts

• AC/DC Adapter modula
• Capacitors
• Resistors
• PIR Sensor
• Transistor
• LED panel

Description

The electronic circuit design like in Figure 1 above show you DIY Motion Sensor Light using LED Bulb and PIR Sensor that written by Narasimha Rao. 

According Circuitstoday blog mentioned that this project is a DIY Smart Light Adapter – which aims to build a smart light bulb based on your ordinary light bulb (which can be a CFL or an LED lamp) and a PIR sensor. The final output will be a light bulb that turns ON based on motion around a particular area within the range of PIR sensor attached to the ordinary light bulb. So lets begin!

If you are not willing to re-wire your home for smart lighting or not interested in spending a huge amount of money for the smart lighting system, then this DIY project is for you.

This simple adapter converts normal bulb into a smart Bulb, with the help of a PIR sensor. The mounting of the sensor is done in such a way that the angular position of the sensor can be adjusted, so that, the original position of the batten holder does not affect the sensing of human passage. This is achieved by using a 3.5 mm stereo jack and its socket. However, this type of mounting is up to your will and wish. It’s possible to wire directly without any mounting.

Read More

Electronic Circuits: Simple Temperature to Voltage Converter using NTC and CA3130

8051 Circuit. - This is one of implementation NTC and CA3130 IC to build converter simple temperature to voltage. It is only need small component completed to build converter in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. Simple Temperature to Voltage Converter Circuit using NTC and CA3130 (Source: Eleccircuits)

Component Parts

• Zener Diode
• Capacitors
• Resistors
• NTC
• Variable resistors
• CA3130 IC

Description

The electronic circuit design like in Figure 1 above show you Simple Temperature to Voltage Converter Circuit using NTC and CA3130. 

According Eleccircuits blog mentioned that this is a simple temperature to voltage converter circuit or an Electronic thermometer circuit there. Which will operate in a temperature range of 0 to 24 degrees Celsius (32 to 75 degrees Fahrenheit). The output rate of 500mV per degree Celsius. Which can be read by a normal voltmeter.

To make it easier to find devices thus Temperature sensors of this circuit. So use a coefficient thermistor relatively constant and not linear. However, the temperature range of 0-24 degrees Celsius. This is enough to use a thermometer kind of normal.

The IC1 is op-amp as the difference amplifier. There are inputs as bridge circuit include with R1 to R4, by at R1,R2,R3 and P1 is a constant arms of the bridge. And R4 is an arm of Bridget’s changing values. The voltage across between R1 and R2 have about 3.4V at zero degree Celsius. The P1 is calibrated to the output of op-amp is 0V.

There are conditions of the NTC, the NTC resistance at higher temperature is decreased, the voltage drop across NTC reduced. Making the output of the Op amp with higher voltage. IF the output is not 0.5V degrees Celsius, Then increase or decrease the R8 and R9 but to reduce or increase to equal the two.

Read More

Electronic Circuits: 24-48V to 5V – 3A DC-DC Converter using BD9G341AEF

8051 Circuit. - This is one of implementation ofElectronic Circuits: 24-48V to 5V – 3A DC-DC Converter using BD9G341AEF to build converter DC to DC. It is only need small component completed to build converter in this time.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Image Courtesy of Electronics-lab

Component Parts

• BD9G341AEFJ
• Capacitors
• Resistors
• Diode
• Inductor

Description

The electronic circuit design like in Figure 1 above show you DC to DC converter using BD9G341AEF. 

According Electronics-lab blog mentioned that 24-48V input voltage range 3A output current DC-DC Converter using BD9G341AEFJ IC from ROHM semiconductor. This IC is ideal for high voltage to low voltage converter with 3A output current. Pin configuration of the board with 3 Pin horizontal mounting of the regulator is similar to LM7805 LDO regulator and is suitable to use this IC as replacement which can provide more current and take high voltage input.

Different voltage output are possible by changing few components. Refer to datasheet for the same. Example circuit can provide 5.1V/3A with input supply range 24-48V DC and operating frequency 200 KHz.

The BD9G341AEFJ is a buck switching regulator with integrated 150mΩ power MOSFET. Current mode architecture provides fast transient response and a simple phase compensation setup. The operating frequency is programmable from 50kHz to 750kHz. Additional protection features are included such as Over Current Protection, Thermal shutdown and under voltage lockout. The under voltage lockout and hysteresis can be set by external resistor.

Read More

Electronic Design: RF based Home Automation Circuit using 8051

8051 Circuit. - This is one of implementation of 8051 microcontroller IC and RF transmitter and reciever to build RF home automationsystem. It is only need small component completed to build this electronic circuit that basically component like relay.

The electronic design circuit of RF based home automation circuit using 8051 is look like in Figure 1 and Figure 2 below. Other component used like LCD, relay, transistor, etc.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. RF Reciever of Home Automation circuit using 8051 (Source: Electronicshub.org)

Figure 2. RF Transmitter of Home Automation circuit using 8051 (Source: Electronicshub.org)

Component Parts

• AT89C51 Microcontroller
• 8051 programming board
• Electrolytic capacitor – 10µF, 16V
• 10KΩ Resistor x 2
• Push button
• 11.0592 MHz crystal
• 22pF capacitors x 2
• 1KΩ x 8 Resistor Pack
• Pot – 10KΩ
• 434 MHz RF Receiver Module
• HT-12D Decoder IC
• 33KΩ Resistor
• LED
• Connecting wires
• 1N4007 Diode
• 2N2222 NPN Transistor
• 1KΩ Resistor
• 12V Relay
• 434 MHz RF Transmitter Module
• HT-12E Encoder IC
• 750KΩ Resistor
• Push Buttons x 4

Description

The electronic circuit design like in Figure 1 above show you RF based home automation circuit using 8051 IC. 

According Electronicshub blog mentioned that the main component of the RF based Home Automation is the RF Module. An RF Module is a small electronic circuit which is used to transmit or receive data wirelessly.

RF Modules are often used in consumer applications where you need to remotely control some machines or appliances without making any physical contact with them.

Some of the common applications are wireless alarm systems, garage door openers, industrial remote controls, wireless home automation systems and smart sensor applications.

RF modules do not require line-of-sight operation. Hence, they are often used instead of infrared remote controls.
Depending upon the type of application, the RF module is chosen.

For example, in case of short range wireless control applications, we can use ASK modulated RF Module of frequency 315 MHz or 433 MHz.

Read More

Electronic Design: IC 555 Inverter Circuit using Mosfet

Inverter Circuit. - This is one of implementation of 555 IC and Mosfet to build power inverter system. It is only need small component completed to build this electronic circuit that basically component.

The electronic design circuit of IC 555 Inverter using Mosfet is look like in Figure 1 below. Other component used like resistors, transformer, capacitors, and transistor.

Beside we will show you electronic design circuit and component parts need, we also will give you global description about this circuit. So, please enjoy to continue reading this article until finish and get more useful.

Electronic Circuit Design

Figure 1. IC 555 Inverter Circuit using Mosfet (Source: Eleccircuits)

Component Parts

• IC1_______NE555 timer IC__________________________ = 1 pcs.
• Q1________BC549___NPN 40V 0.5A transistors________ = 1 pcs.
• Q2,Q3_____IRF540___N CHANNEL POWER MOSFET, 100V, 27A, TO-220______ = 2 pcs.
• C1,C2_____0.1uF 100V mylar capacitors_____________________________ = 2 pcs.
• R1________ 4.7K 0.5W resistor___________________________________ = 1 pcs.
• R2________120K 0.5W resistor___________________________________ = 1 pcs.
• R3,R4_______1K______”______”______________________________________ = 2 pcs.
• R5________5.6K______”______”______________________________________ = 1 pcs.
• T1________2A 12V__CT__12V transformer_____________________________ = 1 pcs.

Description

The electronic circuit design like in Figure 1 above show you power inverter circuit using IC 555 and Mosfet. 

According Eleccircuits blog mentioned that IC-NE555 timer is a square wave frequency generator output of 50Hz. The frequency is determined with R2-resistor and C1-capacitor which we set is 50Hz output. Then we use both N-type Mosfet IRF540 (Q2,Q3) as Driver a transformer coil (primary winding). The current of Pin 3 of IC1 will flow two ways, first through R3 to gate of Q2 and, second ways will flow to Q1-transistor BC549 as inverter logic form to reverse signal difference first ways. Next current flow to gate of Q3 to also dirver the transformer. Them cause have AC voltage of 220V to 250V as voltage of battery source 12V to 14.4V.

Read More

Electronic Software: Proteus 8.6 Professional Full Crack for Windows

Proteus Software. - In this article we will continue to give you the next version of Proteus software after we posted the Proteus 8.6 Professional Full Crack for Windows system from this blog. Now we will give you the next version of Proteus 8.6 Professional Full Crack for Windows to complete your collection of this software.

Using ISIS and ARES as their main features, electronic student and hobbyist can do electronic design simulation and PCB layout easily. You can download Proteus 8.5 SP0 Professional Full with Patch for Electronic Software Design

Image Courtesy of Izofile

In this time, we will give you one of the oldest version of Proteus software that called with Proteus 8.6 Professional Full Crack for Windows system for electronic software design. Beside we will give you description we also will allow you to take free download Proteus 8.6 Professional Full Crack for Windows according the link given in this blog. So, please enjoy and read continue this article until finish.

Description

From Izofile describe that Proteus 8.6 Pro free download is a software which can be used to draw schematics, PCB layout, code and even simulate the schematic. It has a well organized interface which has almost all the necessary tools and the commands also in it which build circuit boards and test them. Proteus 8.6 crack is actually made for the advanced users and they must have a good grasp on it. The software has a simple method with which you can load one of the many sample that Proteus PCB Design comes with.

Download Proteus final version and get a helpful interactive simulations in it which can view and edit the properties of every element on the board. Also the customizations in it go to the depths for each of them. Overall this software demonstrates that it is one of the best softwares in this category. This software design Suite is wholly unique in offering the ability to co-simulate both high and low-level micro-controller code in the context of a mixed-mode SPICE circuit simulation.

Features of Proteus 8.6 Professional Full Crack

1. Its a handy ciruit verifyign and also building software.
2. It is specialize in the circuit boards.
3. Well organized interface.
4. It is made for the advanced users.
5. It contains very helpful interactive simulations.

How to Install and Crack of Proteus 8.6

1. First of all, Install Proteus SP0 8.4 (select the installation type “Custom”)
2. Then, Specify the license file: “Grassington North Yorkshire.lxk”
3. After that, Apply patch “Update Proteus 8.4 SP0 Demo to PRO ENG v1.0.exe”. Be sure to adjust the destination folder! Default Proteus install is under Program Files (x86)…
4. Now, Install Proteus_8.6_SP2_Pro.exe over the existing installation @ C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional
5. Then, Delete the duplicated shortcut labeled “Proteus 8 Professional” located @ C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Proteus 8 Professional\. Delete the one with an older time stamp.
6. Finally, Enjoy!

System Requirement

• Operating System: Windows XP/Vista/7/8/10
• Memory (RAM): 3 GB of RAM
• Hard Disk Space: 600 MB of free space required.
• Processor: Intel 2 GHz or faster

Download

And now you can click the links below to download Proteus 8.6 Professional Full Crack for Windows freely and easily.

Download Proteus 8.6 Professional Full Crack for Windows | 505 MB

Read More